![high headroom high impedance preamp high headroom high impedance preamp](https://w8q2y4p3.stackpathcdn.com/content2/wp-content/uploads/2020/10/stan_front-1.jpg)
In the case of a shorted speaker line or overheating condition, outputs mute automatically until the fault condition is resolved. The AMP-X75 features protection against overheating, shorted or overloaded speaker lines, excessive input signals, and other faults. Whether mounting in a rack, attaching to a flat surface, or placing on a shelf, it’s easy to combine multiple amplifiers into a single assembly. Rack and surface mount parts are included, so there are no other mounting accessories or rack shelves to purchase. The amplifier ships complete with all the hardware required for installation. The AMP-X75 is housed in a quarter-width rack-mountable form factor that can be installed individually or ganged together with other units in a single rack space. The AMP-X75 is high-density stackable with other Crestron modular amplifiers, allowing multiple units to be installed vertically in an equipment rack without needing extra ventilation space. The efficient design ensures cool running operation and long‑term reliability. An internal universal power supply ensures consistent performance at varying line voltages. Advanced Class D technology maximizes efficiency to reduce power consumption and heat dissipation. The AMP-X75 is engineered to deliver exceptional performance and reliability with low distortion, low noise, and high power headroom. NOTE: Each configuration can output up to its respective power rating. Balanced and unbalanced inputs are summed for simultaneous use. Balanced and unbalanced inputs are available for connection to a single stereo or two mono source(s) via detachable terminal blocks or a 3.5 mm TRS connector. The AMP-X75 is a 2-channel amplifier (up to 35 W per single‑ended, low impedance channel) which can also be configured for a single channel of bridged operation (up to 75 W for the bridged channel), or for a single channel of high impedance operation (up to 75 W) to drive a distributed speaker system (70V or 100V).
HIGH HEADROOM HIGH IMPEDANCE PREAMP INSTALL
Whether you need a stereo amplifier that mounts on a wall or under a table, or a high impedance speaker run fed from a rack mounted unit, the AMP-X75 is simple to specify and install in any configuration. Будем благодарны.The Crestron® AMP-X75 is a high performance, space saving, energy efficient amplifier that’s totally configurable, yet simple to use. The PSU input is protected against reverse polarity and over-voltage up to 24V. We recommend a regulated, isolated power supply rated for 100 mA minimum. Power: 9V DC, 2.1 mm center negative barrel. This control is capable of high volumes in order to access quieter clean settings and to properly drive an external power amp. The “Brite” channel is fully muted when this control is at zero.īass, Midrange, Treble: 3-band FMV EQ with the same moderately mid-scooped voicing as the original amp: highly interactive and nonlinear, but familiar. Adds bite to the drive tone at higher settings.
![high headroom high impedance preamp high headroom high impedance preamp](https://cdn.algam.net/pub/produits/produits/vox/MVO-MV50-CR-5-B.png)
The normal channel is fully muted when this control is at zero.īrite: turn clockwise to add gain from the parallel “Brite” channel, which is voiced for extra midrange and sparkle. Higher settings produce a thicker gain sound. Normal: turn clockwise to add gain from the parallel “Normal” channel, which has a neutral voicing. This greatly expands its capabilities beyond a typical drive pedal: the Model feT can be used directly into a power amp, cab simulation, or DAW. This broadens the range of gain and-in the true spirit of the original amp-allows for massive headroom and volume output.
![high headroom high impedance preamp high headroom high impedance preamp](https://sound-au.com/articles/high-z-f8.gif)
This pedal goes beyond the standard triode-to-JFET emulation approach with the inclusion of an emulated power amp.
![high headroom high impedance preamp high headroom high impedance preamp](https://w8q2y4p3.stackpathcdn.com/content2/wp-content/uploads/2021/05/stanley_pre_front.jpg)
Thus, the Model feT is designed to sound good on its own and with other pedals stacked in front. Most famous Model T tones come from putting a distortion or fuzz in front of the amp. In fact, on its own it is a rather clean amplifier with a tone that is dark yet clear and present-making it an exceptional pedal platform. Those who have played the original know that while it excels at heavy tones when pushed, it is far more than just an amp for stoner rock and doom metal. The Model feT is a transistor-based preamplifier designed around the legendary Sunn Model T amplifier.